FCC 76.640 Revised as of October 1, 2014
Goto Year:2013 |
2015
§ 76.640 Support for unidirectional digital cable products on digital cable
systems.
(a) The requirements of this section shall apply to digital cable
systems. For purposes of this section, digital cable systems shall be
defined as a cable system with one or more channels utilizing QAM
modulation for transporting programs and services from its headend to
receiving devices. Cable systems that only pass through 8 VSB broadcast
signals shall not be considered digital cable systems.
(b) No later than July 1, 2004, cable operators shall support
unidirectional digital cable products, as defined in § 15.123 of this
chapter, through the provisioning of Point of Deployment modules (PODs)
and services, as follows:
(1) Digital cable systems with an activated channel capacity of 750 MHz
or greater shall comply with the following technical standards and
requirements:
(i) SCTE 40 2003 (formerly DVS 313): "Digital Cable Network Interface
Standard" (incorporated by reference, see § 76.602), provided however
that with respect to Table B.11, the Phase Noise requirement shall be
-86 dB/Hz, and also provided that the "transit delay for most distant
customer" requirement in Table B.3 is not mandatory.
(ii) ANSI/SCTE 65 2002 (formerly DVS 234): "Service Information
Delivered Out-of-Band for Digital Cable Television" (incorporated by
reference, see § 76.602), provided however that the referenced Source
Name Subtable shall be provided for Profiles 1, 2, and 3.
(iii) ANSI/SCTE 54 2003 (formerly DVS 241): "Digital Video Service
Multiplex and Transport System Standard for Cable Television"
(incorporated by reference, see § 76.602).
(iv) For each digital transport stream that includes one or more
services carried in-the-clear, such transport stream shall include
virtual channel data in-band in the form of ATSC A/65B: "ATSC Standard:
Program and System Information Protocol for Terrestrial Broadcast and
Cable (Revision B)" (incorporated by reference, see § 76.602), when
available from the content provider. With respect to in-band transport:
(A) The data shall, at minimum, describe services carried within the
transport stream carrying the PSIP data itself;
(B) PSIP data describing a twelve-hour time period shall be carried for
each service in the transport stream. This twelve-hour period
corresponds to delivery of the following event information tables:
EIT-0, -1, -2 and -3;
(C) The format of event information data format shall conform to ATSC
A/65B: "ATSC Standard: Program and System Information Protocol for
Terrestrial Broadcast and Cable (Revision B)" (incorporated by
reference, see § 76.602);
(D) Each channel shall be identified by a one- or two-part channel
number and a textual channel name; and
(E) The total bandwidth for PSIP data may be limited by the cable
system to 80 kbps for a 27 Mbits multiplex and 115 kbps for a 38.8
Mbits multiplex.
(v) When service information tables are transmitted out-of-band for
scrambled services:
(A) The data shall, at minimum, describe services carried within the
transport stream carrying the PSIP data itself;
(B) A virtual channel table shall be provided via the extended channel
interface from the POD module. Tables to be included shall conform to
ANSI/SCTE 65 2002 (formerly DVS 234): "Service Information Delivered
Out-of-Band for Digital Cable Television" (incorporated by reference,
see § 76.602).
(C) Event information data when present shall conform to ANSI/SCTE 65
2002 (formerly DVS 234): "Service Information Delivered Out-of-Band for
Digital Cable Television" (incorporated by reference, see § 76.602)
(profiles 4 or higher).
(D) Each channel shall be identified by a one-or two-part channel
number and a textual channel name; and
(E) The channel number identified with out-of-band signaling
information data should match the channel identified with in-band PSIP
data for all unscrambled in-the-clear services.
(2) All digital cable systems shall comply with:
(i) SCTE 28 2003 (formerly DVS 295): "Host-POD Interface Standard"
(incorporated by reference, see § 76.602).
(ii) SCTE 41 2003 (formerly DVS 301): "POD Copy Protection System"
(incorporated by reference, see § 76.602).
(3) Cable operators shall ensure, as to all digital cable systems, an
adequate supply of PODs that comply with the standards specified in
paragraph (b)(2) of this section to ensure convenient access to such
PODS by customers. Without limiting the foregoing, cable operators may
provide more advanced PODs (i.e., PODs that are based on successor
standards to those specified in paragraph (b)(2) of this section) to
customers whose unidirectional digital cable products are compatible
with the more advanced PODs.
(4) Cable operators shall:
(i) Effective April 1, 2004, upon request of a customer, replace any
leased high definition set-top box, which does not include a functional
IEEE 1394 interface, with one that includes a functional IEEE 1394
interface or upgrade the customer's set-top box by download or other
means to ensure that the IEEE 1394 interface is functional.
(ii) Effective July 1, 2011, include both:
(A) A DVI or HDMI interface and
(B) A connection capable of delivering recordable high definition video
and closed captioning data in an industry standard format on all high
definition set-top boxes, except unidirectional set-top boxes without
recording functionality, acquired by a cable operator for distribution
to customers.
(iii) Effective December 1, 2012, ensure that the
cable-operator-provided high definition set-top boxes, except
unidirectional set-top boxes without recording functionality, shall
comply with an open industry standard that provides for audiovisual
communications including service discovery, video transport, and remote
control command pass-through standards for home networking.
[ 68 FR 66734 , Nov. 28, 2003, as amended at 76 FR 40279 , July 8, 2011]
return arrow Back to Top
Subpart L--Cable Television Access
return arrow Back to Top
CiteFind - See documents on FCC website that
cite this rule
Want to support this service?
Thanks!
Report errors in
this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please
help us improve these rules by clicking the Report FCC Rule Errors link to report an error.